Applying Reconfigurable Computing to Acoustic Sensors Using FPGAs

A hybrid-computing architecture using FPGAs collects, processes, and reports data from acoustic and other sensors.

A novel microsensor processing architecture allows a field-programmable gate array (FPGA) to act as a reprogrammable preprocessor or coprocessor to a general-purpose processor (GPP). The FPGA does most of the computationally complex pieces of the algorithm, while the GPP is lightly loaded, performing control, communications, and housekeeping tasks (Figure 1). The flexible architecture supports a wide range of low-power applications, while still being able to leverage emerging commercial technology.

Figure 1. The FPGA-DSP Combination. The architecture allows the FPGA to act as a reprogrammable preprocessor or coprocessor to a GPP.

FPGAs are well suited to the development of deeply pipelined datapath applications typical in signal processing, while GPPs are better suited to system control and communication applications. This commonality in processing requirements led to the development of the Common Architecture for Microsensors (CAµS), which consists of a data acquisition module, digital signal processing (DSP) module, and FPGA module. CAµS is independent of a specific I/O technology and provides a large amount of user-defined digital I/O for interconnection to a variety of devices. The architecture can easily accommodate different radio technologies. The software and hardware can be programmed (configured) through a serial port with support to change the nonvolatile memory in situ. This nonvolatile memory is able to store four separate system configurations (DSP and FPGA configurations). Future work will provide the capability to remotely configure the system.

The system is partitioned into a sensor head, signal conditioning and processing, communication, and battery. An obvious system configuration is to integrate the processing, communication, and battery into a base unit, and the user could then attach sensor heads as needed for the application. Such a system could even act as a gateway for or a manager of a distributed sensor network. The system is based on a commercially available DSP and FPGA in a standard PC-104 form factor (4 × 4" stackable cards). The system consists of either four or five cards: the DSP card, a power card, a data acquisition card, and one or two FPGA cards, depending on the application.

The FPGA module consists of an FPGA and five static RAM memories of 256 k × 36 bits each. Connections between the FPGA and the other boards allow the FPGA to control the data acquisition module and to interrupt the DSP. Additionally, the FPGA is connected to the DSP bus, making it possible to memory- map FPGA resources into the DSP address space.

The first CAµS application developed was an acoustic sensor system for ground-vehicle detection and bearing estimation (Figure 2). The sensor array is formed by a collection of omnidirectional microphones, each providing 360° field-of-view coverage. The sensors are placed on or near the ground in a geometric shape to conform the array. The microphone array consists of seven microphones, six in an 8-foot-diameter circle and one in the center. The signals received at each of the microphones are sampled at 1 kHz and the resulting data are multiplied by a windowing function. After a corner turn of the data, seven 1,024-point Fast Fourier Transforms (FFTs) are performed.

A detection algorithm is then run on the FFT output magnitudes to identify possible targets. This is done in two stages. First, a peak picking algorithm estimates the noise floor and high-power frequency bins are selected with a threshold determined from that noise floor. Harmonic line analysis is performed to find groups of frequency bins that form a harmonic relationship. Groups containing enough frequency components are declared to be targets. In the second stage, beamforming is performed on the raw data at the target’s frequencies to determine exact target bearings. Finally, a tracking filter is applied to reduce the number of false reports and provide a lock on the target’s bearing, providing lines-of-bearing (LOB) updates once every second. This entire computation could be done on either the CAµS DSP or the CAµS FPGA alone.

Figure 2. In the circular Acoustic Sensor Array, the sensors are placed on or near the ground in a geometric shape to conform the array.

Future work will focus on adapting CAµS for use with additional sensors and on miniaturizing the CAµS architecture. In this future microsensor system, the FPGA-based processor will be capable of supporting magnetic, acoustic, seismic, and imaging (day or infrared) sensors all in the same package. The FPGA will have to be reconfigured in real time to facilitate such a sensor suite.

This work was done by Mark Falco of Sanders and Andree Filipov of the Army Research Laboratory.


This Brief includes a Technical Support Package (TSP).
Applying Reconfigurable Computing to Acoustic Sensors Using FPGAs

(reference ARL-0036) is currently available for download from the TSP library.

Don't have an account? Sign up here.