Bi-Axial Vibration Energy Harvesting
This technique can be used to capture airframe vibrational energy, and convert it into electrical power.
For air platforms, the installation of Structural Health Monitoring (SHM) systems is complicated by the fact that the majority of SHM devices need to be fitted on internal aircraft structure, underneath the aircraft’s skin. If the SHM device is in a location that is difficult to access, then powering the device may be problematic because traditional powering methods are generally not feasible. For example, replacing batteries on many SHM devices deployed across a fleet would be impractical, and accessing an onboard power system to supply SHM devices may lead to flight worthiness and certification issues.
To address this powering issue, the use of vibration energy harvesting (VEH) has been investigated. Two unresolved scientific issues that inhibit the use of VEH on aircraft are: (1) the need for a wide operational frequency bandwidth to permit harvesting from the frequency- rich vibration that can be present on airframes, and (2) the need for a multi-axial harvesting approach, since aircraft vibrations are typically not uni-axial. Previous work addressed the first issue by developing the vibro-impacting energy harvesting approach that produced VEH over a broader operational bandwidth compared with many other harvester approaches, including harvesters that are currently commercially available.
The second fundamental issue with most VEH approaches (again, including all known commercial vibration energy harvesters) is that they are uni-directional, and hence can only harvest vibrational energy from host accelerations along a single axis. Therefore, while a considerable amount of scientific literature exists on the topic of VEH, none to date reports on a technique to effectively harvest from bi-axial host accelerations.
A bi-axial approach represents a significant advancement in VEH; specifically, the approach increases the operational directionality from single-axis to 360 degrees in a plane. Furthermore, this design uses a magnet/bearing cantilever analogue (replacing the cantilever design used by many harvesters), potentially allowing a significant reduction in harvester volume. This design also uses an oscillating ball bearing to create magnetic flux steerage through a magnetoelectric laminate transducer to generate harvestable electrical power.
The concept involves three main components: (1) a sensor mounted inside the aircraft at a difficult-to-access location is monitoring in-flight mechanical loads on an airframe, (2) with the sensor utilizing energy that is parasitically harvested from local airframe vibrations by an energy harvester, (3) when the aircraft is on the ground, a wireless link— the acoustic electric feedthrough—is used to download sensor data and simultaneously provide additional energy to the sensor unit.
The bi-axial vibration energy harvesting approach can harvest energy from the multi-axis accelerations experienced by an aircraft. A bi-axial oscillator was created using a permanent-magnet/ballbearing arrangement. The magnet produces a bi-axial restoring force on the bearing, and as the bearing oscillates, it steers magnetic field through a magnetostrictive/ piezoelectric laminate transducer, thereby producing an oscillating charge that can be harvested.
Modeling was used to make a qualitative assessment of the magnetic flux changes in the ME transducer as the bearing oscillates, which indicated that large flux variations occur as the bearing moves from the magnet’s central-line towards the edge. A simple laboratory demonstrator of a biaxial ME energy harvester was created using a Terfenol-D/lead zirconate titanate/Terfenol-D transducer. Harvester output was measured as a function of drive-angle, host acceleration, and load resistance. The harvester produced a peak rms power of 121 mW from an rms host acceleration of 61 mG at 9.8 Hz.
This work was done by Scott Moss, Joshua McLeod, Ian Powlesland, and Steve Galea of the Defence Science and Technology Organisation. DSTO-0002
This Brief includes a Technical Support Package (TSP).
Bi-Axial Vibration Energy Harvesting
(reference DSTO-0002) is currently available for download from the TSP library.
Don't have an account? Sign up here.
Top Stories
INSIDERManned Systems
Turkey's KAAN Combat Aircraft Completes First Flight - Mobility Engineering...
INSIDERMaterials
FAA Expands Boeing 737 Investigation to Manufacturing and Production Lines -...
INSIDERImaging
New Video Card Enables Supersonic Vision System for NASA's X-59 Demonstrator -...
INSIDERManned Systems
Stratolaunch Approaches Hypersonic Speed in First Powered TA-1 Test Flight -...
INSIDERUnmanned Systems
Army Ends Future Attack and Reconnaissance Helicopter Development Program -...
ArticlesEnergy
Can Solid-State Batteries Commercialize by 2030? - Mobility Engineering...
Webcasts
AR/AI
From Data to Decision: How AI Enhances Warfighter Readiness
Energy
April Battery & Electrification Summit
Manufacturing & Prototyping
Tech Update: 3D Printing for Transportation in 2024
Test & Measurement
Building an Automotive EMC Test Plan
Manufacturing & Prototyping
The Moon and Beyond from a Thermal Perspective
Software
Mastering Software Complexity in Automotive: Is Release Possible...