Cryogenic-Capable Isolators Improve the Performance of Millimeter-Wave Systems by Lowering Noise Levels
Silence is golden when it comes to filtering out unwanted reflected noise, especially in extremely high-frequency, millimeter-wave (MMW) applications. While recent improvements in isolator designs are solving many of these problems, one critical challenge remains: finding isolators that operate optimally under cryogenic conditions.
For manufacturers of ultra-high-frequency wireless applications such as 5G and 6G communications, standoff security scanning, and military defense products, the issue of MMW and cryogenics is relatively new. In fact, some system designers may still be unaware that an isolator built to operate at room temperatures will fail to operate optimally when temperatures are reduced to cryogenic levels.
“That happened to us,” said Alexander Anferov, a graduate research assistant in the Schuster Lab at the University of Chicago. “We tried using regular isolators from one vendor. We cooled them down and assumed they would work, but they weren’t behaving right.”
Anferov, a recent Caltech graduate, looked to NASA and its Jet Propulsion Laboratory in Pasadena, CA, for a solution. “It turned out they had just commissioned a grant for a company to design isolators specifically for cryogenics,” said Anferov. “After talking with them, it became obvious from shared experiences that we were actually causing the problem in our setup by utilizing isolators that could not stand up to extremely cold conditions.”
Due to the fact that there is no industry standard, MMW manufacturers often, though unintentionally, make components out of metals that when cooled to cryogenic levels, start superconducting.
“That completely changes the device properties for the worse,” added Anferov. “The real issue is that the results are unpredictable. Surprise resonances and new leakage paths can crop up and power that used to be absorbed can be reflected instead.”
A Universal Challenge
Antenna designers are very familiar with the constant battle of standing waves. Without control, these unwanted waves reflect back into the transmitter to attenuate power output while raising unwanted noise input. Especially in the MMW bands that cover the frequencies between 30 GHz and 500 GHz, the reduction of transmitted signal strength jeopardizes the battle — almost literally in military applications.
To reduce the voltage standing wave ratio (VSWR) and help increase the signal-to-noise (S/N) ratio, microwave engineers typically rely on isolators (aka Faraday rotation isolators). These discrete components allow electromagnetic signals to pass in one direction but absorb them in the opposite direction, thus reducing noise. Dana Wheeler, CEO of Massachusetts-based Plymouth Rock Technologies, explains how standard isolators often become problematic with next-generation electronics that require components that must withstand more extreme environments.
“We received a Small Business Innovation Research (SBIR) grant from the Navy to decrease the size of the large satcom antenna systems on aircraft carriers in order to put them higher up onto the ship’s superstructures because the jet blast from the new fighter planes was damaging the radomes,” explained Wheeler. “The challenge was to lower the weight and size without losing any performance.”
Wheeler explained that for any antenna system, if you shrink the size of the antenna aperture, gain (G) drops by a logarithmic amount, which is in contrast to the goal. But if you can lower the noise temperature (T), then you can get back the gain that was lost. “Our solution was to cryogenically cool the low-noise amplifier,” said Wheeler. “We can get down to less than 100 Kelvins with commercially available cryo-coolers,” he said. “Our biggest challenge was finding an isolator that could perform at those temps. Fortunately for us, a company called Micro Harmonics had just designed some specifically for NASA.”
Headquartered in Virginia, Micro Harmonics specializes in design solutions for components used in MMW products. Under a NASA contract awarded in 2015, the company successfully developed an advanced line of isolators for 50 GHz to 330 GHz applications. That successful project led NASA to award the company a subsequent grant to address the issue of isolators at cryogenic temperatures.
“Low-noise integrated circuit amplifiers work because of the nature of a Schottky diode or a FET transistor, in that as it gets cooler, it has lower noise,” said Wheeler. “However, cryogenic low-noise amplifiers are not cheap. With ferrite isolators, you get more bang for the buck: a better gain-over-noise figure at room temperatures and even more so at cryogenic temps.”
There are numerous material issues that must be addressed to ensure that an isolator is able to withstand the rigors of thermal cycling. The substantial temperature dependence of the ferrite magnetization is also a challenge. Ferrite magnetization follows a modified Bloch law, increasing by more than 20% when cooled from room temperature down to 4 K. As the temperature decreases, there is less thermal energy and it is easier to align magnetic dipoles in the ferrite.
The design used by Micro Harmonics compensates for the change. It also uses magnetic armatures designed to achieve a focused, uniform bias field in the ferrite. This strong magnetic saturation allows the shortest possible length of ferrite — hence, small footprint — while achieving a low insertion loss of less than 1 dB at 75-110 GHz and only 2 dB at 220-330 GHz.
While manufacturers are now realizing the benefits of isolators for cryogenics applications, on the research side, Anferov and his team at the University of Chicago are on a mission to see just how low they can go.
“Our lab does experiments at 1 Kelvin and there are components that can function at temperatures close to absolute zero,” said Anferov. “However, at the extremely high frequencies demanded by today’s applications, it takes a specialized ferrite isolator to perform consistently under such extremes — a ferrite that won’t over-rotate the field and create unwanted issues.”
It is essential for any MMW application that each isolator is tested over the full frequency band on a vector network analyzer (VNA) to ensure compliance. This includes reliability testing (Belcore) and cryogenic cycling tests. Comprehensive VNA test data should back up every component since there are often signatures in the data that can be missed. “Knowing that isolators would now perform in the MMW bands at single-digit Kelvin temperature was good news for us because that was one less component we had to worry about,” said Anferov.
For Wheeler’s mil-spec work, the cryogenic isolators will help ensure the reliability of Plymouth Rock’s technology and products. “In harsh environments, the contaminants on the radome of the antenna can really add to the system noise figure due to reflections (VSWR),” said Wheeler. “By integrating a cryogenic isolator in front of your low-noise receiver, you will realize a reduction in the noise and increase the gain ratio.”
This article was contributed by Micro Harmonics, Fincastle, VA. For more information, visit here .
University of Rochester Lab Creates New 'Reddmatter' Superconductivity Material...
MIT Report Finds US Lead in Advanced Computing is Almost Gone - Mobility...
INSIDERElectronics & Computers
Airbus Starts Testing Autonomous Landing, Taxi Assistance on A350 DragonFly...
Boeing to Develop Two New E-7 Variants for US Air Force - Mobility Engineering...
PAC-3 Missile Successfully Intercepts Cruise Missile Target - Mobility...
Air Force Pioneers the Future of Synthetic Jet Fuel - Mobility Engineering...
Specifying Laser Modules for Optimized System Performance
The Power of Optical & Quantum Technology, Networking, &...
How to Achieve Seamless Deployment of Level 3 Virtual ECUs for Automotive...
Manufacturing & Prototyping
Tailoring Additive Manufacturing to Your Needs: Strategies for Performance and...
Driver-Monitoring: A New Era for Advancements in Sensor Technology
Electronics & Computers
Leveraging Machine Learning in CAE to Reduce Prototype Simulation and Testing
Real Time Physiological Status Monitoring
ArticlesMechanical & Fluid Systems
Reducing the High Cost Of Titanium
Solving Military Satellite, Radar and 5G Communications Challenges with...