Optimizing DSP Techniques for Antenna Site Software Radio
Many applications can benefit from pushing software radio functions up the mast to the antenna as a viable alternative to traditional rack-mounted receiver systems. New technology offers engineers of Software Defined Radio (SDR) systems diverse opportunities to apply digital signal processing (DSP) much closer to the antenna than ever before. Various strategies include the latest wideband data converters, monolithic receiver chips, compact RF tuners, and remote receiver modules using gigabit serial interfaces. Each approach presents benefits and tradeoffs that must be considered in choosing the optimal solution for a given application.
Strategies for the Latest Wideband Data Converters
With the emergence of monolithic A/D converters capable of sampling rates of 5 GHz and higher, engineers can now directly digitize analog RF signals covering a frequency span of more than 2 GHz. This allows the capture of wideband communications and radar signals in a single data stream, eliminating the complexity of splitting a given band into parallel adjacent sub-bands, and the inevitability of input signals straddling them. While these new converters appear to simplify software radio architectures, they also impose many limitations and tradeoffs.
RF signals from the antenna must first be amplified, filtered, and possibly down-converted in frequency to match the input voltage range and usable input bandwidth of the A/D converter. Optimal amplifier gain boosts the strongest signal to the full-scale input range of the A/D. Further amplification to boost weaker in-band signals will cause overloading the A/D, which destroys the signal integrity for all signals. Thus, even one strong interferer will reduce the achievable dynamic range for weaker signals. This significant tradeoff occurs whenever a single A/D is used to handle a large number of signal types in a wide frequency span. To make matters worse, as sampling rates increase, A/D converters deliver lower Effective Number of Bits (ENOB) ratings. For example, a 5-GSample/sec 10-bit A/D converter may only deliver an ENOB of 7.6 bits.
Also, filtering is imperative to eliminate all energy outside the frequency span of interest. Otherwise, aliasing will fold out-of-band noise and adjacent signals into the digitized signal stream, degrading signal-to-noise performance and adding spurious signals.
Lastly, A/D data arriving at several GSamples/sec will overload most DSPs. Data de-interleaving hardware is often built into the A/D to help implementation of the electrical interface, but even so, every data sample must somehow be processed, stored, or transferred. The latest families of field-programmable gate arrays (FPGAs) are especially well suited, not only in dealing with these extremely high data interface rates, but also in processing signals in real time.
One product example is the Pentek 71641 3.6-GHz A/D and Digital Down Converter (DDC) XMC module. It features a 12-bit 3.6-GSample/sec A/D converter coupled to a Virtex-6 FPGA. The A/D de-interleaves samples into eight parallel 12-bit streams, delivering samples to the LVDS ports of the FPGA at 450 MSamples/sec each. Inside, eight parallel engines implement a DDC that tunes across the 1.8 GHz input band (Figure 1). It performs frequency translation to baseband and provides digital filtering of the complex baseband output samples. Selectable output bandwidths of 90, 180, or 360 MHz, representing tunable slices of the input spectrum, are delivered to the system through a native PCIe Gen 2 x 8 interface.
New classes of monolithic silicon receivers offer an impressive integration of diverse RF analog circuitry required to implement a complete software radio tuner front end. These low-cost devices accept input signals directly from the antenna and deliver amplified, translated, and filtered analog baseband outputs suitable for low-speed A/D converters or demodulator chips.
For example, the Maxim MAX2112 targets satellite set-top and VSAT applications including 8PSK modulation and Digital Video Broadcast (DVB-S2) applications. It uses an LNA to boost antenna input signals falling between 925 and 2175 MHz, as well as a programmable gain RF amplifier for 80 dB of overall gain control.
An integrated VCO and programmable fractional-N frequency synthesizer drive a quadrature mixer to tune across the entire input frequency range, down-converting any input signal to I+Q baseband. These baseband signals are band limited with a pair of low-pass filters, programmable from 4 to 40 kHz. This extremely high level of integration on a single chip dramatically reduces the size and cost of the receiver, and is ideal for applications restricted in space, power, weight, and cost or requiring a large number of channels.
However, while these devices work well for applications requiring only modest signal-to-noise ratios like satellite signal interception, they are not suitable for some of the more demanding government and military systems for communications, signal intelligence, and radar.
Compact RF Tuners
These higher dynamic range requirements require better RF analog signal processing including multi-conversion designs, amplifiers with lower noise figures, local oscillators with better phase noise and wider tuning ranges, mixers that minimize unwanted spurs, and filters with better pass band flatness, roll off, and stop band performance. Other critical factors include packaging, shielding, isolation, voltage regulation, vibration tolerance, and thermal performance. Boosting overall performance of the system is achieved by progressively improving the weakest of these signal chain elements in iterative cycles until the desired result is reached.
Each level of improvement leads directly to system-level performance benefits such as lower bit error rates for digital communication systems, improved target detection range and classification accuracy for radar systems, higher intelligibility of voice interceptors, and the enhanced precision of target location and trajectory for weapons control systems.
As a result, there is a continuum of required software radio performance levels matching the operational objectives and constraints of a wide range of systems. At the low end, the monolithic receiver described above may suffice, while a very sensitive SIGINT receiver might require a large, highly sophisticated RF subsystem.
As another factor, many applications need to cover only a limited range of input signal frequencies, such as an upper-band GSM receiver handling signals between 1,700 and 2,000 MHz. For these band-limited systems, simpler single-conversion RF tuner architectures can still deliver good performance. In these systems, a single local oscillator and mixer down-convert the RF signal to a lower-frequency IF signal compatible with a high-resolution A/D converter. Of course, judicious selection of amplifiers and filters, and careful analysis and suppression of mixer products, are essential design tasks.
Because of the narrow tuning range, these types of RF tuners are often called “slot receivers.” They can be ideal for dedicated applications where limited frequency coverage, cost, size, and weight enable placement of the tuner at or near the antenna.
One example is the Pentek 8111 Slot Receiver. An input bandpass filter rejects signals outside of the defined RF tuning “slot,” helping to eliminate both out-of-band noise and discrete signal interferers. The mixer and tunable local oscillator translate the RF input down to an IF frequency of 225 MHz. An IF bandpass filter excludes all signals outside an 80-MHz band centered at 225 MHz, delivering an analog output suitable for 14- or 16-bit A/D converters (Figure 2).
Low-noise amplifiers and programmable attenuators in the signal chain boost antenna signal levels to match the fullscale input voltage of the A/D. Seven different models each cover a different 400 MHz slot between 800 MHz and 3 GHz. An overlap of 100 MHz between adjacent slots ensures that any 80-MHz signal band can be accommodated.
Serial Fabrics, FPGAs, and Remote Receivers
Delivering high-frequency RF signals through long coaxial cables from the antenna to the receiver system has several disadvantages. First, the higher the frequency, the more signal loss in the cable. To mitigate this, Low Noise Blocks (LNBs) located on the antenna are commonly used to down-convert signals above 4 GHz (C-band and higher) to a lower frequency, typically in the L-band (1-2 GHz). Nevertheless, cables carrying these analog signals still suffer degradation and present EMI radiation and susceptibility issues. Not only do they impose a tangible weight impact in aircraft and unmanned aerial vehicles (UAVs), they also become maintenance burdens for the extremely long runs and the salt environment aboard ships.
The proliferation of industry-standard gigabit serial digital links offers many benefits in transmission and distribution of these digitized receiver signals. For example, GbE and 10 GbE links are so widely deployed in computer networks, WAN and LAN servers, and data processing centers that commercial competition has driven down costs of components, switches, bridges, cables, and other infrastructure.
In the embedded computing market, FPGA vendors not only offer built-in PCIe ports, they also offer native lightweight gigabit serial protocols such as Xilinx’s Aurora and Altera’s SerialLite. These, along with SerialFPDP, are ideal for delivering raw A/D or baseband I+Q samples from an FPGA-based front end. At the receiving end, host bus adapters are available for all of these protocols, and many embedded systems processors have native interfaces for SerialRapidIO and PCIe.
Each of these gigabit serial links can be delivered over copper or optical cables. Single-mode fiber cables can connect data from remote receivers up to 10 km away. This benefits large antenna array installations that must collect signals from a grid of widely spaced antennas. Optical cables are free from EMI radiation, eliminating interference to other electronics in tightly packed manned and unmanned aircraft, as well as offering security against eavesdropping. They are also immune to EMI pickup from powerful transmitters, motors, and generators found in shipborne installations. Lastly, optical cables are much lighter than copper cables and are highly resistant to moisture, salt, and chemicals.
FPGAs can implement essential DDC functions and deliver digital baseband samples across an industry-standard digital gigabit serial link. Because these links are full-duplex, the same cable provides a path for control and status functions for the host. Digital receiver data can be easily distributed to multiple destinations using low-cost switches and readily archived on storage servers.
For sensitive signals and classified information, data encryption can be easily included before transmission. Additional preprocessing algorithms such as radar pulse-compression, FFT energy calculations, scanning, and threshold detection can be incorporated within the FPGA to reduce transmission data rates and offload these processing tasks from the host system.
Rethinking Software Radios
There is no substitute for appropriate analog RF signal conditioning prior to A/D conversion, and each technique outlined represents its own application-specific tradeoffs. Nevertheless, the added benefits of antenna site software radio receivers are numerous.
This article was written by Rodger Hosking, Vice President at Pentek in Upper Saddle River, NJ. For more information, Click Here .
University of Rochester Lab Creates New 'Reddmatter' Superconductivity Material...
MIT Report Finds US Lead in Advanced Computing is Almost Gone - Mobility...
INSIDERElectronics & Computers
Airbus Starts Testing Autonomous Landing, Taxi Assistance on A350 DragonFly...
Boeing to Develop Two New E-7 Variants for US Air Force - Mobility Engineering...
PAC-3 Missile Successfully Intercepts Cruise Missile Target - Mobility...
Air Force Pioneers the Future of Synthetic Jet Fuel - Mobility Engineering...
Specifying Laser Modules for Optimized System Performance
The Power of Optical & Quantum Technology, Networking, &...
How to Achieve Seamless Deployment of Level 3 Virtual ECUs for Automotive...
Manufacturing & Prototyping
Tailoring Additive Manufacturing to Your Needs: Strategies for Performance and...
Driver-Monitoring: A New Era for Advancements in Sensor Technology
Electronics & Computers
Leveraging Machine Learning in CAE to Reduce Prototype Simulation and Testing
Real Time Physiological Status Monitoring
ArticlesMechanical & Fluid Systems
Reducing the High Cost Of Titanium
Solving Military Satellite, Radar and 5G Communications Challenges with...