MOBILITY ENGINEERING Produced by SAE Media Group
MOBILITY ENGINEERING
Magazines
Magazine cover

Current Issue

Archives

Magazine cover

Current Issue

Archives

Magazine cover

Current Issue

Archives

Magazine cover

Current Issue

Archives

Silicon Carbide Junction Field-Effect Transistor Devices for Scalable Solid-State Circuit Breakers

Semiconductor devices used as contactors help prevent power electronic converter damage.

Power electronic converters functioning as components in high-power systems, such as those of hybrid military ground vehicles, require fast fault isolation, and in most cases, benefit additionally from bidirectional fault isolation. To prevent converter damage or failure, fault current interrupt speeds in the hundreds of microseconds to few millisecond range are necessary. Presently used mechanical contactors do not provide adequate actuation speeds, and suffer severe degradation during repeated fault isolation. Instead, it is desired to use a large array of semiconductor devices having a collectively low conduction loss to provide large current-handling capability and fast transition speed for current interruption.

The back-to-back VJFET Test Configuration.The bidirectional snubber was connectedacross the parts. An isolated DC power supplywas used as a source, and a 50-ohm load wasconnected in series with the VJFETs.
A solid-state contactor for protection of a non-isolated DC-DC converter was developed. A solid-state contactor was designed with silicon carbide (SiC) metal oxide semiconductor field-effect transistors (MOSFETs) placed in parallel. A large number of 20A rated SiC MOSFET die were placed in parallel to handle in excess of 500A of current with the desired 1V conduction drop across the part. To behave like a mechanical contactor by stopping current flow in both directions, the MOSFET-based contactor would require an additional set of paralleled MOSFETs placed in series with, but in the opposite direction of, the original set (back-to-back MOSFETS) with the source terminal of the MOSFETs connected together. This added set of MOSFETs would effectively double both the number of devices needed, and the amount of contactor loss compared to original estimates.

The SiC Junction Field Effect Transistor (JFET) was considered as a possible candidate for use instead of a MOSFET in the design of a solid-state contactor. In this application, a normally-on JFET would provide operation as a circuit breaker, interrupting current when actuated, much like fault protection provided by circuit breakers in utility power systems. Due to the lack of a parasitic body diode between the drain and source terminals of the JFET, it was suggested that a single device may be capable of bidirectional current conduction and bidirectional voltage blocking. A bidirectional snubber was designed to reduce solid-state breaker voltage stress during fault isolation. Simulations were conducted to determine suitable component ratings based on estimated worst-case line inductances.

Northrop Grumman Corporation (NGC) developed SiC normally-on vertical JFETs (VJFETs) having current ratings of 20A and 50A with respective blocking voltages as high as 1900V and 1200V. Smaller 8A rated sample VJFET parts were obtained for scaled-down application testing. An isolated driver was designed and built to provide an adjustable gate-to-source (VGS) bias of nominally +2V for VJFET conduction, and an adjustable VGS bias down to –24V for blocking conditions. The driver was tested on a small capacitive gate load.

After the VJFET asymmetries were characterized, the parts offered advantages over MOSFETs in a back-to-back configuration. Compared to MOSFETs, VJFETs offer higher operating temperatures due to the absence of an oxide layer. Present VJFETs also have lower on-state resistances for a given chip area. Finally, VJFETs have significantly lower gate capacitances resulting in faster transition speeds.

Evaluation of the parts was done in a simple test setup. Two 8A VJFET parts were connected in a back-to-back configuration with common sources. The bidirectional snubber was connected across the parts. An isolated DC power supply was used as a source, and a 50-ohm load was connected in series with the VJFETs. The setup allowed the connections of the VJFET pair to be easily reversed for bidirectional testing. The driver was connected with the gate line to the gates of both VJFETs through individual 5-ohm resistors, and with the source line connected to the common source of both parts.

For the back-to-back VJFET configuration to function properly in this application, either a reduced VGS (for at least the reverse conducting device) is required, or enough pairs of devices must be connected in parallel to keep to the voltage drop between the source and drain of the reverse conducting device below 1V. In either case, these actions would effectively de-rate the devices by nearly a factor of two, causing almost twice as many back-toback device pairs to be required for a given current level. To apply a reduced on-state VGS to only the reverse conducting device would also increase gate driver complexity, in addition to the sensing and conditioning needed to determine current direction for sending proper gating delays.

This work was done by Damian P. Urciuoli of the Army Research Laboratory. For more information, download the Technical Support Package (free white paper) at www.defensetechbriefs.com/tsp  under the Electronics/Computers category. ARL-0092

Topics:
Aerodynamics Architecture Connectors and terminals Drag Electrical systems Electronic equipment Electronics & Computers High voltage systems Parts Research and development Semiconductor devices Transistors Vehicle drivers Vehicle occupants
This Brief includes a Technical Support Package (TSP).
Document cover
Silicon Carbide Junction Field-Effect Transistor Devices for Scalable Solid-State Circuit Breakers

(reference ARL-0092) is currently available for download from the TSP library.

Don't have an account?

More From SAE Media Group

    Magazine cover
    Defense Tech Briefs Magazine

    This article first appeared in the February, 2010 issue of Defense Tech Briefs Magazine (Vol. 4 No. 1).

    Read more articles from this issue here.

    Read more articles from the archives here.

    Overview

    The document titled "Evaluation of SiC VJFET Devices for Scalable Solid-State Circuit Breakers" by Damian P. Urciuoli, published in May 2008, investigates the application of Silicon Carbide (SiC) Vertical Junction Field Effect Transistors (VJFETs) in the development of scalable solid-state circuit breakers. The research is particularly relevant for high-power systems, such as those used in hybrid military ground vehicles, where fast fault isolation is critical.

    The introduction emphasizes the need for efficient fault isolation in power electronic converters, which are essential components in high-power applications. The report outlines the advantages of bi-directional fault isolation, which enhances the reliability and safety of these systems.

    The document is structured into several sections, beginning with an investigation using MOSFETs, followed by an exploration of parallel SiC JFETs, and concluding with a detailed analysis of back-to-back VJFET configurations. Each section discusses the performance characteristics, advantages, and potential applications of these devices in solid-state circuit breaker technology.

    The investigation into MOSFETs provides a baseline for understanding the performance of traditional semiconductor devices in fault isolation applications. The subsequent section on parallel SiC JFETs highlights the benefits of using SiC technology, such as higher efficiency, better thermal performance, and the ability to operate at higher voltages and temperatures compared to conventional silicon devices.

    The core of the report focuses on back-to-back VJFETs, which are proposed as a promising solution for scalable solid-state circuit breakers. The analysis includes electrical characteristics, switching performance, and the potential for integration into existing power systems. The findings suggest that SiC VJFETs can significantly improve the speed and reliability of fault isolation, making them suitable for demanding applications in military and industrial settings.

    In summary, the document presents a comprehensive evaluation of SiC VJFET devices, demonstrating their potential to enhance the performance of solid-state circuit breakers. The research findings contribute to the ongoing development of advanced power electronic systems, emphasizing the importance of innovative semiconductor technologies in achieving efficient and reliable fault isolation in high-power applications. The report is approved for public release, ensuring that its insights are accessible to a broader audience interested in power electronics and solid-state technology.

    Top Stories

    INSIDERDesign

    Feature Image Venus Aerospace’s Rotating Detonation Rocket Engine Completes First Flight...

    INSIDERDesign

    Feature Image Bombardier is Digitally Upgrading its Aircraft Design, Engineering and...

    INSIDERDefense

    Feature Image How the US Army is Advancing Research in Robotics, AI and Autonomy

    INSIDERManned Systems

    Feature Image New Copper Alloy Could Provide Breakthrough in Durability for Military Systems

    Original EquipmentManned Systems

    Feature Image ACT Expo 2025: Heavy-Duty EVs, H2 Trucks and Tariff Talk Dominate Day One

    Technology ReportPower

    Feature Image ICE and Hybrid-Electric Propulsion Show Staying Power

    Webcasts

    Similar Stories

    BriefsEnergy

    Feature Image Energy-Filtered Tunnel Transistor: A New Device Concept Toward Extremely Low...