Deep Breathing for EV Batteries
Optimum venting is a key to maximizing EV battery pack performance and safety. An expert offers five important design considerations.
As batteries become more sophisticated, the need to protect them from the elements has never been greater. Battery pack engineers understand vehicle applications and by marrying them with proper venting technology, they are helping to advance electric vehicle performance and safety.
Below are five important design considerations to help maximize EV battery pack performance:
1. Provide pressure equalization
Temperature and elevation changes can cause pressure variations inside a pack enclosure. Vents allow air to flow in and out of the enclosure, which helps equalize the pressure. Higher airflow allows faster equalization and lower maximum pressure differentials. As pressure builds in an operating system, the weakest point will be found, so a properly designed vent takes the pressure off sensitive components within a vehicle and helps maintain proper airflow.
The rate of pressure change also needs to be considered. Pressure changes are often driven by temperature changes inside the battery pack due to environmental conditions, charging, and discharging. As the rate of pressure change increases, higher airflow is required.
To handle fluctuating pressure changes, the size and number of vents, type of membrane, airflow properties, and outside conditions need to be considered at the onset of development. Implementing the appropriate type and number of battery pack vents can help manage the internal pack pressure at differential operating conditions.
2. Engineer for ingress protection
While airflow requirements are critical to managing pressure levels in battery packs, ingress protection to keep out contaminants is also an important consideration. A key parameter to use during the design and testing phases is the ingress protection (IP) rating, which indicates the effectiveness of sealing enclosures against foreign bodies and moisture.
Typical contaminants a battery vent must protect against include water (spray and submersion), oil, dust, and sand particles. Donaldson’s dual-stage battery vents, for example, utilize a unique body design and Tetratex ePTFE membrane – a proprietary filtration media – to provide exceptional battery pack protection.
As ingress protection is increased, emergency degassing airflow may be decreased, so proper venting solutions need to find the optimal balance between ingress protection and degassing airflow.
3. Account for edge cases
EV battery packs and enclosures are created to handle unexpected edge cases, which are events that occur at extreme operating parameters. While edge cases occur infrequently, it’s important that a venting solution is optimized to help reduce the risk of damage to the battery pack and mitigate component failure or costly repair.
Examples of edge-case scenarios include:
- DC fast charging: This charging process is significantly faster than regular charging stations and generates extra heat and pressure on an EV battery.
- Hill climbs: The competitive sport of uphill racing (i.e., Pike’s Peak) causes a sudden change in altitude and increases the pressure and temperature in a vehicle battery.
- Water fording: Driving off-road through a creek can put a warm battery pack in thermal shock and cause a rapid vacuum event from the cool water.
- Air transportation: A vehicle being transported within a cargo aircraft will be impacted by pressure changes from the altitude variation.
- Rock impact: Rocks or other hard debris hitting the undercarriage of a vehicle can cause a pressure spike inside the battery pack.
Our testing process includes a comprehensive design failure mode and effect analysis. This analysis looks at the severity and frequency of possible edge cases and tracks them in a validation plan. We work with customers to understand what extreme conditions their vehicles may experience and what requirements are needed to retain driving performance during a sudden edge case scenario.
4. Mitigate emergency degassing events
As with edge cases, optimum battery pack vent design helps manage emergency degassing events, such as a thermal runaway. Such events happen when pressure rises to a concerning level and gas needs to be immediately released from the pack.
Dual-stage venting solutions are designed to help manage escalated situations. Stage one equalizes pressure while preventing the ingress of water and contaminants. Stage two venting fully opens in response to rapid pressure and heat buildup to allow expanding gases to escape and reduce further damage to remaining cells. In most situations, a single vent assembly can accomplish both functions. This mechanism helps prevent further damage to battery cells or a pack enclosure.
5. Perform a full temperature-range validation
Our engineering and product teams design battery pack vents to operate in a variety of operating temperatures. We frequently perform tests in a full range of extreme temperatures to see how our vents handle burst pressure, emergency degassing, pressure cycle, thermal cycle, thermal soak, thermal shock, and vibration.
Venting is a critical component of EV battery thermal management. As temperatures rise or fall, a breathable vent provides pressure equalization to protect battery housing seals. We work directly with OEMs to ensure our vents are tested across the full range of temperatures experienced in an EV battery pack.
The demand for innovative EV batteries that provide more power and longer range will continue, with advanced battery pack vent designs playing a major role. They must protect against any element that arises while on the road.
Shane Campbell, a graduate chemical engineer and product-development veteran, is a product manager in Donaldson’s Integrated Venting Solutions business unit.
Top Stories
INSIDERManufacturing & Prototyping
Boeing to End 767 Production, Reduce Workforce Amid Ongoing Union Strike
INSIDERManufacturing & Prototyping
Army Receives New Robot Combat Vehicle Prototypes
INSIDERRF & Microwave Electronics
Germany's New Military Surveillance Jet Completes First Flight
INSIDERManufacturing & Prototyping
Army Evaluates 3D Printing for Bradley Fighting Vehicle's Transmission Mount
INSIDERAerospace
Army Seeks to Expand 3D Printing to the Tactical Edge
ArticlesPropulsion
Cummins New X15 Engine Meets Upcoming Regs While Boosting Efficiency
Webcasts
Transportation
The Rise of Software-Defined Commercial Vehicles
Automotive
Avoiding Risk Analysis Pitfalls: Implementing Linked DFMEA, HARA,...
Automotive
A Quick Guide to Multi-Axis Simulation and Component Testing
Software
Best Practices for Developing Safe and Secure Modular Software
Defense
Countering the Evolving Challenge of Integrating UAS Into...