Room-Temperature Sub-Diffraction-Limited Plasmon Laser
Plasmon lasers can provide new capabilities for bio-sensing, data storage, photolithography, and optical communications.
Lasers present the means to deliver powerful, coherent, and directional high-frequency electromagnetic energy. However, the diffraction limit of light imposes fundamental constraints on how compact such photonic devices can be and their potential for integration with electronic circuits, which are orders of magnitude smaller.
Room-temperature plasmon laser operation below the diffraction limit demands effective cavity feedback, low metal loss, and high gain — all within a single nanoscale device. A semiconductor plasmon laser operating at room temperature has been developed. A 45-nm-thick cadmium sulphide (CdS) nanosquare atop a silver surface separated by a 5-nm-thick magnesium fluoride gap layer provides the sub-diffraction-limited mode confinement and low metal loss. Although the high-index material is only 45-nm thick, the surface plasmons of this system carry high momentum — even higher than light waves in bulk CdS or plasmonic nanowire lasers. This leads to strong feedback by total internal reflection of surface plasmons at the cavity boundaries.
The close proximity of the high-permittivity CdS square and silver surface enables modes of the CdS square to hybridize with SPPs of the metal-dielectric interface, leading to strong confinement of light in the gap region with relatively low metal loss. The coupling is extremely strong and causes a dramatic increase in the momentum with respect to the modes of the CdS square alone. As the dominant magnetic-field component of the waves is always parallel to the metal surface, these are called transverse magnetic (TM) waves. On the other hand, waves with dominant electric field parallel to the metal surface (transverse electric or TE) cannot hybridize with SPPs. Consequently, they become increasingly delocalized as the gap size decreases and are effectively pushed away from the metal surface with a corresponding decrease in momentum with respect to TE waves of the CdS square alone.
Although both wave polarizations are free to propagate in the plane, only TM waves have sufficient momentum to undergo total internal reflection and achieve the necessary feedback for lasing. Although CdS squares thicker than about 60 nm can support TE waves with sufficient momentum to undergo total internal reflection, they are scattered out of the plane more effectively than TM waves because they are delocalized from the metal surface.
This laser can be considered to be a SPASER (surface plasmons amplified by stimulated emission of radiation), since it generates plasmonic cavity eigenmodes and only emits light to the farfield as a side-effect of scattering. The current device exhibits multiple laser peaks attributed to the number of available modes in the square cavity configuration. Single-mode plasmon lasing was observed in irregularly shaped devices with lower symmetry where only a limited number of modes can undergo total internal reflection.
The intense fields that are generated and sustained in the gap region make such lasers highly useful for investigating light-matter interactions. Namely, an emitter placed in this gap region is expected to interact strongly with the laser light. Such light-matter interaction enhancements are also observable to a lesser extent in the CdS gain medium; under weak pumping, the CdS bandedge transitions of this plasmon laser show a spontaneous emission lifetime reduced by a factor of 14.
This work was done by Ren-Min Ma, Rupert F. Oulton, Volker J. Sorger, and Guy Bartal of the National Science Foundation Nanoscale Science and Engineering Centre, University of California, Berkeley; and Xiang Zhang of Lawrence Berkeley National Laboratory for the Air Force Office of Scientific Research. AFOSR-0001
This Brief includes a Technical Support Package (TSP).

Room-Temperature Sub-Diffraction-Limited Plasmon Laser
(reference AFOSR-0001) is currently available for download from the TSP library.
Don't have an account?
Top Stories
INSIDERAerospace
Clean Sky Demonstrator Fuselage Shows Potential of Thermoplastics in Aircraft...
INSIDERAerospace
Blue Origin Rocket Reaches Intended Orbit on First Launch
INSIDERAerospace
Can Microvanes Improve Fuel Efficiency for Legacy Air Force Aircraft?
NewsConnectivity
Closing Gap to Leverage Enhanced Computational Power for SDV Advancement
INSIDERSoftware
The Future of Aerospace: Embracing Digital Transformation and Emerging...
INSIDERAerospace
Researchers Achieve Breakthrough in New Design of Superconducting Quantum...
Webcasts
Aerospace
Improving Thermal Management for Aerospace and Defense Electronics
Automotive
The Road Ahead for Next-Gen E/E Architectures: Trends and...
Electronics & Computers
Department of Defense Contracts Denied: New Cybersecurity Rules...
Software
Leveraging Simulation for Net Zero Emissions in Conventional and...
Materials
Quickly Prototyping Custom Textures on Automotive Parts
AR/AI
AI-Powered Quality Control for Sustainable Automotive Production